alchin 1.5 scale traction engine HELP

alchin 1.5 scale traction engine HELP

This topic has 4 replies, 4 voices, and was last updated 12 October 2024 at 20:16 by noel shelley.

Viewing 5 posts - 1 through 5 (of 5 total)

Author

Posts
12 October 2024 at 12:57 #758950
joseph tatler
Participant
@josephtatler55359
I am making the Alchin 1.5 scale using Hughes book.

I am wondering if anyone can help by scanning or copying the dimensions of the reversing link that is on sheet 6 of the drawings.

the link dimensions in the book are not very clear as the fold is actually on the link diagram.

I would extremely grateful if anyone can help.

regards

Joe
Advert

12 October 2024 at 13:36 #758953
noel shelley
Participant
@noelshelley55608
Sheet 6 in the book is of little help giving no meaningful dimensions, this is why you have to buy the drawings from Reeves. Chapter 18 , page 171 tells how to make it and the radius is 4.5″. I don’t have the drawings but someone here may have. Good Luck. Noel.
12 October 2024 at 13:44 #758956
Phil P
Participant
@philp
If you send me a private message with your email address, I have a PDF which will give you the dimensions you need.

Phil
12 October 2024 at 15:40 #758964
JasonB
Moderator
@jasonb
It is all on sheet 8 pg 136-137 of the book and quite readable. Sheet 6 is just how it goes together.
12 October 2024 at 20:16 #759005
noel shelley
Participant
@noelshelley55608
Joe, Jason is right ! It’s drawing 8 and though on the fold of the book I can read it which dimensions do you need ? Noel.
Author

Posts

Viewing 5 posts - 1 through 5 (of 5 total)

Please log in to reply to this topic. Registering is free and easy using the links on the menu at the top of this page.

Code of Conduct

Latest Replies

Viewing 25 topics - 1 through 25 (of 25 total)

- Topic
- Voices
- Posts
- Last Post
- How would you do this?
  Started by: moonman in: Beginners questions
- 3
- 3
- 23 December 2024 at 01:01
  Michael Gilligan
- Help for DIY lathe build.
  Started by: moogie in: Help and Assistance! (Offered or Wanted)
- 9
- 10
- 22 December 2024 at 23:45
  not done it yet
- Warco 720 1 2
  Started by: Mick Bailey in: Manual machine tools
- 12
- 27
- 22 December 2024 at 23:38
  not done it yet
- Discussion on the Future Direction of Model Engineer and Workshop 1 2 3 4
  Started by: Neil Wyatt in: Model Engineer.
- 45
- 90
- 22 December 2024 at 23:32
  IanT
- Stuart Steam Boiler Feed Pump – Cylinder Scrapped
  Started by: David Deaville in: General Questions
- 4
- 4
- 22 December 2024 at 23:25
  Paul Lousick
- How to sort this problem out.
  Started by: Michael Callaghan in: Workshop Techniques
- 9
- 11
- 22 December 2024 at 23:11
  Mick Bailey
- Drill press will not start
  Started by: AStroud in: Help and Assistance! (Offered or Wanted)
- 7
- 8
- 22 December 2024 at 22:16
  Charles Lamont
- ELS for BOXFORD AUD 1 2 3
  Started by: Speedy Builder5 in: Workshop Tools and Tooling
- 17
- 57
- 22 December 2024 at 19:40
  Robert Atkinson 2
- Recommissioning a small vertical boiler
  Started by: Mark Salzedo 1 in: General Questions
- 7
- 18
- 22 December 2024 at 19:24
  Mark Salzedo 1
- Replacement Motor Wiring
  Started by: Gary Lynch in: General Questions
- 3
- 3
- 22 December 2024 at 19:06
  noel shelley
- Dial gauge troubles
  Started by: Roger Hart in: Workshop Tools and Tooling
- 9
- 13
- 22 December 2024 at 14:35
  Mick B1
- L5 issue
  Started by: Neil Taylor in: Beginners questions
- 6
- 11
- 22 December 2024 at 10:43
  Emgee
- Drilling holes in boiler banding.
  Started by: Michael Callaghan in: Hints And Tips for model engineers
- 8
- 10
- 22 December 2024 at 07:03
  JasonB
- Model Engineering Survey – What Do YOU make? 1 2 3 4
  Started by: SillyOldDuffer in: General Questions
- 52
- 80
- 21 December 2024 at 23:01
  SillyOldDuffer
- Microscope marking objective
  Started by: old mart in: Clocks and Scientific Instruments
- 6
- 16
- 21 December 2024 at 20:48
  old mart
- new life for old chuck
  Started by: old mart in: Workshop Tools and Tooling
- 1
- 1
- 21 December 2024 at 20:18
  old mart
- Some VERY interesting LED modules 1 2 … 5 6
  Started by: Michael Gilligan in: Electronics in the Workshop
- 18
- 131
- 21 December 2024 at 19:23
  SillyOldDuffer
- 775 Motor based Dynamo ? 1 2
  Started by: JasonB in: Miscellaneous models
- 6
- 47
- 21 December 2024 at 18:48
  JasonB
- Sable 2015 Desktop CNC / engraver
  Started by: Bazyle in: CNC machines, Home builds, Conversions, ELS, automation, software, etc tools
- 9
- 17
- 21 December 2024 at 17:54
  John Haine
- GRIPTRU Chuck adjust
  Started by: Speedy Builder5 in: Workshop Techniques
- 12
- 19
- 21 December 2024 at 14:31
  Michael Gilligan
- What did you do Today 2024 1 2 … 20 21
  Started by: JasonB in: The Tea Room
- 75
- 518
- 21 December 2024 at 14:30
  bernard towers
- Miniatur Wunderland
  Started by: Paul Lousick in: Miscellaneous models
- 3
- 3
- 21 December 2024 at 11:30
  noel shelley
- The Future of Model Engineer and Model Engineers’ Workshop magazines.
  Started by: Neil Wyatt in: Model Engineer.
- 8
- 11
- 21 December 2024 at 07:09
  JasonB
- 30 Year old MOTORUN 3 Phase Static converter 1 2 3 4
  Started by: mr fixit in: Introduce Yourself – New members start here!
- 16
- 85
- 20 December 2024 at 21:55
  John Hinkley
- Sacrificial pin
  Started by: Bernard Start in: The Tea Room
- 14
- 20
- 20 December 2024 at 21:47
  old mart

Viewing 25 topics - 1 through 25 (of 25 total)

View full reply list.

Latest Issues

Issue 4758

January 2025

Buy Latest/Back Issues

Newsletter Sign-up

Latest Replies