Ml2

Advert

New Replies

Report Bug

Help/FAQs

Ml2

This topic has 8 replies, 5 voices, and was last updated 7 May 2021 at 18:47 by Robert Atkinson 2.

Viewing 9 posts - 1 through 9 (of 9 total)

Author

Posts
6 May 2021 at 19:22 #543561
David Herrington
Participant
@davidherrington80098
Hi I have just bought a ml2 for a restoration project and I want to strip down the headstock, I have removed the grub screws from the pulley and bull gear and removed the threaded collar on the left hand side and undone the top clamp screws, with a soft mallet I tapped the left hand end to drive out the spindle , it moved about 5 mm that’s all, any ideas please
Advert

6 May 2021 at 19:22 #38614
David Herrington
Participant
@davidherrington80098
Spindle removal
6 May 2021 at 20:04 #543569
roy entwistle
Participant
@royentwistle24699
Is there by any chance another grub screw in either of the holes that you have removed one from ?
6 May 2021 at 21:01 #543579
David Herrington
Participant
@davidherrington80098
Roy

i have checked and there are no more grub screws in the holes, the large gear wheel spins freely but the pulley and small gear does not spin
6 May 2021 at 21:07 #543581
Lee Rogers
Participant
@leerogers95060
Posted by roy entwistle on 06/05/2021 20:04:03:

Is there by any chance another grub screw in either of the holes that you have removed one from ?

Spot on from Roy . On any old machine always check for a second grubscrew. Clean anything that may conceal a taper pin and touch it over with a marker pen, wipe the ink off and look for a tell tale mark is another regular check(not your problem here though I guess).
6 May 2021 at 21:19 #543584
Robert Atkinson 2
Participant
@robertatkinson2
I had problems removing the spindle from my ML2. The issue turned out to be somone had tightened the pointed grub screw in the bullgear away from the intended recess and raised burrs on the spindle. not much you can do about it other than brute force or miving the spindle / gear positions back to where they were and using some kind of long end cutting tool down the grubscrew hole to remove the burrs.
Mine scored the front bearing on the way out.

Robert G8RPI.
6 May 2021 at 21:44 #543589
David Herrington
Participant
@davidherrington80098
Hi it looks like the same thing has happed here, the pointed grub screw has damaged the shaft. I will have to remove the damage before proceeding, can you tell me is the small gear part of the pulley assembly
7 May 2021 at 11:24 #543661
Georgineer
Participant
@georgineer
Posted by Robert Atkinson 2 on 06/05/2021 21:19:37:

I had problems removing the spindle from my ML2. The issue turned out to be somone had tightened the pointed grub screw in the bullgear away from the intended recess and raised burrs on the spindle. not much you can do about it other than brute force or miving the spindle / gear positions back to where they were and using some kind of long end cutting tool down the grubscrew hole to remove the burrs.
Mine scored the front bearing on the way out.

Robert G8RPI.

Exactly this. I had the same on my ML4.

George B.
7 May 2021 at 18:47 #543747
Robert Atkinson 2
Participant
@robertatkinson2
Posted by David Herrington on 06/05/2021 21:44:41:

Hi it looks like the same thing has happed here, the pointed grub screw has damaged the shaft. I will have to remove the damage before proceeding, can you tell me is the small gear part of the pulley assembly

Yes it is.

That is a replacement for my original fibre one which has split.

HTH,

Robert.
Author

Posts