DRO with 65 tooth bullwheel

DRO with 65 tooth bullwheel

This topic has 1 reply, 1 voice, and was last updated 9 July 2009 at 14:35 by Douglas Johnston.

Viewing 2 posts - 1 through 2 (of 2 total)

Author

Posts
9 July 2009 at 14:35 #42236
Douglas Johnston
Participant
@douglasjohnston98463
My letter in the latest issue of MEW (153) asked about creating 60 pulses from a 65 tooth gear in the lathe. Since writing the letter I have been trying to answer my own question by delving into the internet and using an electronics forum. I have been told about an interesting chip which can be used for this (CD4089BE) and using two of these chips cascaded in the add mode provides the correction needed to a very acceptable degree of accuracy (about 0.1%).I found a supplier of these chips on ebay and am waiting for delivery.
I still feel however there may be a simpler electronic solution so if you can come up with one lets have it.

Douglas
Advert

9 July 2009 at 14:35 #37946
Douglas Johnston
Participant
@douglasjohnston98463
Author

Posts

Viewing 2 posts - 1 through 2 (of 2 total)

Please log in to reply to this topic. Registering is free and easy using the links on the menu at the top of this page.

Code of Conduct

Latest Replies

Viewing 25 topics - 1 through 25 (of 25 total)

- Topic
- Voices
- Posts
- Last Post
- 100g +/- 0.1 mg metrology weight standard?
  Started by: Ian P in: Workshop Tools and Tooling
- 4
- 5
- 19 November 2024 at 05:24
  Alan Charleston
- Restoration of a Watchmaker’s Drill Press
  Started by: Michael Gilligan in: Suggested Online Resources
- 1
- 1
- 19 November 2024 at 01:45
  Michael Gilligan
- Which motor ?
  Started by: here again in: Manual machine tools
- 5
- 10
- 19 November 2024 at 01:33
  here again
- Using relays
  Started by: Graham Titman in: General Questions
- 10
- 20
- 19 November 2024 at 01:05
  Michael Gilligan
- boiler leak
  Started by: Bill Dawes in: Locomotives
- 10
- 18
- 18 November 2024 at 23:23
  Bill Dawes
- 30 Year old MOTORUN 3 Phase Static converter 1 2 3
  Started by: mr fixit in: Introduce Yourself – New members start here!
- 13
- 61
- 18 November 2024 at 22:59
  mr fixit
- DIY Homemade Lamp Running off PM Research Model Generator
  Started by: Blue Heeler in: Stationary engines
- 2
- 3
- 18 November 2024 at 22:21
  Blue Heeler
- MEW 346 creates new definition of ‘universal’,
  Started by: Ian P in: Model Engineers’ Workshop.
- 1
- 1
- 18 November 2024 at 21:38
  Ian P
- What did you do Today 2024 1 2 … 18 19
  Started by: JasonB in: The Tea Room
- 67
- 455
- 18 November 2024 at 20:11
  Nicholas Farr
- New Here
  Started by: garryh in: Introduce Yourself – New members start here!
- 6
- 14
- 18 November 2024 at 19:49
  garryh
- Tap alignment in the mill and lathe? 1 2 3
  Started by: Bo’sun in: Workshop Tools and Tooling
- 21
- 52
- 18 November 2024 at 19:42
  bernard towers
- Wellsaw 4″ Hacksaw Info
  Started by: John McCulla in: Manual machine tools
- 7
- 13
- 18 November 2024 at 19:17
  Pete Rimmer
- Jakobs Gear Hobber from scrap (no casting)
  Started by: celso ari schlichting in: General Questions
- 1
- 1
- 18 November 2024 at 18:37
  celso ari schlichting
- Ultracut 370 alternatives
  Started by: Mick Bailey in: Materials
- 5
- 6
- 18 November 2024 at 17:53
  mark costello 1
- Anybody recognise this design?
  Started by: Paul Kemp in: Stationary engines
- 9
- 15
- 18 November 2024 at 17:53
  John Purdy
- Parvalux motor – help please
  Started by: Mike Waldron in: Manual machine tools
- 13
- 22
- 18 November 2024 at 17:47
  Michael Gilligan
- Hot rolled angle problems 1 2
  Started by: Mick Bailey in: Materials
- 17
- 42
- 18 November 2024 at 14:44
  duncan webster 1
- Interesting Chuck design
  Started by: Vic in: Workshop Tools and Tooling
- 9
- 19
- 18 November 2024 at 13:34
  Vic
- Traction Engine Identification Help Please….
  Started by: Bill Morgan in: Traction engines
- 6
- 6
- 18 November 2024 at 09:19
  noel shelley
- Model Turbines 1 2 … 22 23
  Started by: Turbine Guy in: Stationary engines
- 28
- 571
- 17 November 2024 at 23:02
  duncan webster 1
- Hardy & Padmore “Ideal”
  Started by: JasonB in: I/C Engines
- 4
- 7
- 17 November 2024 at 20:29
  JasonB
- Spring material advice needed
  Started by: old mart in: Materials
- 10
- 16
- 17 November 2024 at 19:33
  old mart
- Myford
  Started by: nick harris 1 in: Introduce Yourself – New members start here!
- 2
- 2
- 17 November 2024 at 17:03
  noel shelley
- 4 Truck Shay 5 inch
  Started by: conrod in: Work In Progress and completed items
- 4
- 13
- 17 November 2024 at 12:44
  Another JohnS
- Belt drive convertion Worco WM16 mill
  Started by: Brian Merrifield in: Manual machine tools
- 4
- 7
- 17 November 2024 at 08:47
  Dell

Viewing 25 topics - 1 through 25 (of 25 total)

View full reply list.

Latest Issues

Issue 4755

December 2024

Buy Latest/Back Issues

Newsletter Sign-up

Latest Replies