Die Holder Sizes

Advert

New Replies

Report Bug

Help/FAQs

Die Holder Sizes

This topic has 10 replies, 8 voices, and was last updated 9 April 2023 at 20:30 by noel shelley.

Viewing 11 posts - 1 through 11 (of 11 total)

Author

Posts
9 April 2023 at 16:06 #640668
Howard Lewis
Participant
@howardlewis46836
Needing to produce a 3/4 x 10 BSW thread, I have been loaned a tao and a Die.

But having no holder for a 2" OD Dies, I need to make one.

Not wishing to over expand the Dies, and crack it, I want to know thew maximum diameter of the recess in the holder., so that the Dies can be adjusted to produce a correctly sized thread. (Screrw cut almost to size and then finish with the Die.

Despite sewsrching in my booksm and an hour's search, on line, have been unable to find anything, other than that the tolerance on Die diameter is

+ / – 0.008"

So should I botre the holder to 2.010", or dare I safely go a shade larger ?

Howard
Advert

9 April 2023 at 16:06 #34200
Howard Lewis
Participant
@howardlewis46836
Size of recess in Holder for Die
9 April 2023 at 16:32 #640670
Ian Parkin
Participant
@ianparkin39383
Howard

just been to measure my die holders…i have a few 2” ones and they are all 18-20 thou over 2”
9 April 2023 at 17:19 #640676
Howard Lewis
Participant
@howardlewis46836
Ian,

Thank You

Was wondering if +010" mwould be too much (havong been loaned the tooling it would be a disaster to over expand the Die and crack it.

Think that I'll get bnracve and bore the holder to 2.015" and tread very carefully..

Now I can start work on the job!

Howard
9 April 2023 at 17:27 #640681
Ian Parkin
Participant
@ianparkin39383
Howard

most of my dies that are 2” are not actually split but solid
9 April 2023 at 17:44 #640683
Clive Foster
Participant
@clivefoster55965
Howard

You need a bit of oversize if the die is to easily go into the holder.

I have one that is less than 5 thou oversize relative to the die diameters and it's a total pain to get dies in and out. Usual method is to screw a stud or similar into it to use as a handle. Its important to get the die seated true against the back of the recess which is hard without a touch of wiggle room.

Clive
9 April 2023 at 17:57 #640684
Harry Wilkes
Participant
@harrywilkes58467
some years back I need to cut a thread on site I had the 2" die but no die holder I managed using a jubilee clip with a screwdriver in the gap, yes bit 'sketchy' but done the job

H
9 April 2023 at 18:30 #640686
bernard towers
Participant
@bernardtowers37738
Best of luck with using a die that size for accurate sizing where you could crewcut it accurately with a lot less effort.
9 April 2023 at 18:39 #640689
Andrew Tinsley
Participant
@andrewtinsley63637
Bernard,

Howard is doing what you suggest, if you read his initial post..

Andrew.
9 April 2023 at 18:48 #640690
DC31k
Participant
@dc31k
Insulation tape or beer can could be used as a spacer between the OD of a die and the ID of its holder if the difference is excessive.

Every (handled, not tailstock) holder I have has three screws in it, one to expand the die and the other two to limit its expansion.
9 April 2023 at 20:30 #640715
noel shelley
Participant
@noelshelley55608
Like DC3 mine have 3 screws so OD not really critical. If your at Heacham I can lend you one. Noel.
Author

Posts