Motor wiring eyelets/crimps type?

Advert

New Replies

Report Bug

Help/FAQs

Motor wiring eyelets/crimps type?

This topic has 11 replies, 9 voices, and was last updated 21 December 2021 at 19:19 by Grindstone Cowboy.

Viewing 12 posts - 1 through 12 (of 12 total)

Author

Posts
20 November 2021 at 13:48 #572150
Bountyboy
Participant
@bountyboy
Hello,

I'm currently rewiring a Kennedy Hexacut saw and I need some help identifying and sourcing the brass eyelet/crimps used to terminate the motor winding to the on/off switch. Please see attached photos, hopefully!

I searched the internet but can't find any info on these crimps, they must be obsolete. I have tried to use normal crimps but the switch cover won't fit on to the motor casing due to the size of the crimps and I'd also like to keep it original if possible.

Any info would be helpful

Thanks in advance
Advert

20 November 2021 at 13:48 #32223
Bountyboy
Participant
@bountyboy
20 November 2021 at 13:55 #572153
Swarf, Mostly!
Participant
@swarfmostly
Hi there,

Your photo looks a bit, I emphasise 'a bit', like a Ross-Courtney termination.

I use them in the terminal chamber of the motor on my ML7. They have the advantage of not having a tail like the modern crimps but they also have the disadvantage of being, apparently, extinct!!!!

If you locate a source, fill your own requirements before blowing the gaff!!!!!!!!

Best regards,

Swarf, Mostly!
20 November 2021 at 14:01 #572158
peak4
Participant
@peak4
As far as I'm aware, they are no longer available.
See this thread for the solution I used when I had a similar problem.
https://www.model-engineer.co.uk/forums/postings.asp?th=128186

The previous photos in the album show the process.
https://www.model-engineer.co.uk/albums/member_album.asp?a=45271 

Bill

Edited By peak4 on 20/11/2021 14:03:18
20 November 2021 at 15:22 #572175
Bountyboy
Participant
@bountyboy
Thanks for the replies and links to other posts. I thought they maybe obsolete but I like the idea of the shoe eyelets, I think I'll look into this.

Cheers
20 November 2021 at 15:36 #572178
David Jenner
Participant
@davidjenner61726
Try here:

https://www.vintagecarparts.co.uk/products/721-container-wiring-terminal.

Regards

Dave J
21 November 2021 at 12:52 #572290
Chris Gunn
Participant
@chrisgunn36534
BB, Presumably you only have a few to do, so try annealing them, and then bend back the tabs, refit the new wire, and tap the tabs back down again with a punch, and then give them a final nip in the vice. You cannot get more original than that.

Chris Gunn
21 November 2021 at 20:10 #572346
Bountyboy
Participant
@bountyboy
Thanks for all your help. I going to buy a shoe eyelet repair kit and give it a go.

Cheers all!
22 November 2021 at 00:17 #572376
bernard towers
Participant
@bernardtowers37738
I’m sure I have a few around, let me know the size and I will investigate.
22 November 2021 at 08:08 #572385
mgnbuk
Participant
@mgnbuk
I recall this type of cable terminal from the works where I started my apprenticeship, but have not seen them since & didn't know what they were called to look them up.

Seems that Ross Courntney ceased trading around 2001. These seem to offer an alternative means to the same end for quite a bit less than the vintagecarparts items.

Nigel B.
29 November 2021 at 17:01 #573505
Oldiron
Participant
@oldiron
Bountyboy check your messages. (inbox at top of page)

regards
21 December 2021 at 19:19 #576175
Grindstone Cowboy
Participant
@grindstonecowboy
Bit late, and others have already described basically the same process, but I just came across this in an old issue of Popular Science magazine…

Rob
Author

Posts