Hi all,

As a complete beginner to this hobby and someone who has only owned a lathe a few weeks I feel I'm now getting past the 'swarf making stage' and have decided to try and built my first steam engine.

I've decided to have a go at this :-

**LINK**

If it proves to be beyond my skill level I'll put it to one side for a few weeks till I have the necessary skills and/or tools to do the job.

The plans are in imperial but I've decided to work in metric (my lathe and measuring equipment are all metric) so whilst I am working to the basic design the measurements are flexible and I'll modify / embellish it as I go along.

As I say I am a complete beginner so if people want to offer me advice or tell me better ways of doing things I'm more than happy to listen.

Here goes :-

Firstly I decided to machine the cylinder block / steam chest, I didn't have a piece of brass big enough to hand so I settled for aluminium (It's unlikely the engine will ever see live steam so I figured aluminium will do for compressed air).

Block turned and faced to size then power piston bore done.

Steam chest bore done, I decided to make this slightly larger diameter than the plans as I think that may prove more forgiving at my skill level.

Ready to begin drilling inlet port.

Drilled through as far as power cylinder, I was a bit relieved at this point. With my limited tools and experience I wasn't certain how parallel the bores were etc. However once the inlet was drilled through my scriber seems to suggest they are reasonably true.

I decided to omit mounting holes for the cylinder at this point as I'm not yet certain how I'll go about it but will probably deviate from the plan.

So – I decided on the piston next. This time I had a suitable piece of brass

I did damage the first piston when I turned it around in the chuck but had better luck second time

I decided to cut in a couple of very small oil rings that aren't on the plan but I thought they may help me get a better airtight seal.

Edited By Peter Nichols on 26/06/2015 12:22:38

Thanks guys.

Ady that thing about rescaling brings back memories, I was taught that at school 40 yrs ago and completely forgot about till you mentioned it. The article also mentions slide rules ! I even remember them from school too

I been having another look at the plans and have decided to try and make the con rods a bit more attractive than the plans and possibly machine the cylinder top off then make a separate bolt on cylinder head, that would make it a bit more attractive and allow me to see what's happening in the cylinders when it comes to adjusting the valve timing.

Peter.

Hi all,

Thanks for the advice, I didn't have a piece of brass the right size so I just used aluminium without thinking too much about it. I've now made the valve/exhaust piston also, with both pistons done they seem to fit nicely and slide smoothly, whether it will run is another matter !

Thinking ahead a little, I'm intending to try it on compressed air, can anyone advise me what is the usual diameter airline for such models so I can machine an appropriate sized inlet fitting ?

The plans go on about soldering a tube etc, I'd rather just insert a threaded fitting to accept a small airline.

Thanks

Peter.

Hi Steve,

I did think about air supply and initially considered an aquarium pump but having since looked around I've seen paint spraying kits with a compressor for just over £60.

Something like this was what I'd thought about :-

**LINK**

I think I'd rather pay the extra and get a spraying kit, it's bound to come in handy for hobby work.

Peter.

Hi,

Although the plans have this as a vertical engine I'd prefer to have it as a horizontal so have been doing a lot of thinking how I might best go about it. Part reason I didn't try a 'wobbler' as a first project was that without access to a milling machine I didn't feel I could reliably file the necessary flat face by hand with sufficient accuracy.

After some helpful advice from other members here they suggested I could face off a piece placed a cross the lathe chuck if I was careful about it.

I decided I wanted to bottom mount the cylinder block and reasoned the only way was to face off in the way others had suggested, with the intention of bolting it to a plate. The cylinder walls are fairly thin and bottom mounting seemed the best option.

I decided to have a test run with a piece of similar sized aluminium and sure enough it worked with ease. At least now I know that till I get a mill it is possible to do very basic 'milling' in the lathe. As this was only a test piece I didn't go to the trouble of lining it up properly but you get the idea.

I figured that lining up would be a problem but with the use of parallels and a few faint scribe markings that were still left from earlier drilling operations I could just about manage. I used the tool point to align with the scribe markings and rotate the work by hand in the chuck 180* whilst not moving the tool.

In order to get access to the scribe markings along the centre line I needed the work out of the chuck slightly beyond its diameter so it's actually only being held firmly by the 2 flat ends with the other 2 chuck jaws gently touching the curved sides. I realise that's far from ideal but the intention is to take light cuts on a soft material and I have got a very firm grip of the flat ends of the work.

Success ! – A bit of filing and tidying up to remove a few minor scrapes and chuck marks and also seems to be ok.

Edited By Peter Nichols on 28/06/2015 15:34:48

Hi Ian,

I found the plans online, this is the link :-

**LINK**

Is it the same as you were thinking off ? I'm broadly working to it but adjusting a few dimensions to suit and intend it to be a horizontal rather than the vertical in the plan.

I'd have liked to start on the con rods and possibly the main axle/crank next but decided I'd be better getting the cylinder mounted on a brass plate and on a piece of scrap wood for now, then I can look at where the crank needs to go etc and finally make the con rods to suit. I indend to make the rods out of round brass bar rather than the flat strips in the plan.

I'm looking at buying a small compressor/airbrushing kit (about £65) as an air supply as the airbrushing is bound to come in handy as well but I did notice aquarium airline on Amazon – £2 with free delivery ! so I ordered some.

Till I've decided how best to clean up the brass base plate I thought for today I'll just do the airline fitting, I didn't think ahead at the time but I decided to risk drilling it out to cut an M8 thread into the cylinder block as I think anything smaller wouldn't pass sufficient air.

The result meant I have an M8 to 4mm airline fitting bored through to 2.5 mm, I wanted to try and bore it out a bit more but though I'd be pushing my luck

I can't say I'm overly happy with the result but the likelihood is it will only be a temporary measure and it does look like it will do the job till I come up with a better idea.

Peter.

Edited By Peter Nichols on 29/06/2015 13:33:44

I started making it using the materials I had, so I'm hoping it will work using the materials I'm using.

It's only ever going to have a few test runs on compressed air till I can get it running then it will be a glorified desk ornament so I'm not overly bothered about wear or efficiency issues so long as I can satisfy myself it is a 'working' model.

Hi Ian,

As I'm only starting out at this game I'm gradually building up a stock of materials (and tools) but for the moment working with what I've got till I have a better stock.

Hi all,

Since I've now decided the engine will be a horizontal rather than a vertical as in the plans I was faced with how to raise the cylinder block a little so that the line of the pistons travel will be in line with the main axle / crank assembly.

I took the rather unorthodox step of raising it on a small brass plinth. (I have limited materials and tools to work with) It may be unusual but I'm satisfied it will work and at least look presentable.

I decided to make the legs appear to be one piece although they are a glorified nut and bolt.

Next I opted to make the power piston con rod, I decided I wanted to make it out of a brass rod turned to size with the ends filed and drilled by hand.

Since the diameter isn't critical I decided to turn between the chuck and a centre and hope I could get it thin enough to look right. I was pleasantly surprised that using this method and a bit of care I was able to get to about 3mm over about 60mm

Half an hour of filing and drilling to arrive at this

So far I'm reasonably pleased with the result and ready to make the piston pin. The holes in the piston and con rod are 1.7mm so I'm hoping I can turn a short rod down to 1.5mm ish.

The pic below is at 1.7mm and just slightly too large, the only way I could figure out to get a few more cuts was to support it by holding a pen behind the work opposite the cutting tool. Not a very precise method admittedly, but it did work on a small workpiece where a good finish isn't important.

A few more careful passes and hey presto 1.5mm, just enough to allow the piston free movement.

I chose to keep a 'head' on one end of the rod and lightly pein the other end.

Which then nicely leaves me to its current state, with a flywheel I made a couple of weeks ago. The wheel wasn't made for this engine and needs tidying up to remove some grooves but with a bit of work may be suitable.

Starting to look a bit like an engine !

Peter.

Hi,

I had been wondering for a while on how best to support the main axle, given the small size of this engine I didn't feel there was enough room to have 2 separate supports and decided I use one relatively large diameter cylinder of mild steel and attempt to machine 2 opposing flat faces where the axle would enter and exit.

Yesterday when I began the task of making the mounting it turned out to be one disaster after another, I struggled to get anything square and at one point even resorted to using a dial indicator on the chuck jaws when I was running out of ideas.

Eventually I did manage to drill the axle hole but it tuned out to be far from parallel to the base. Even in this small photo it's possible to see how far out of line it is.

Trying to machine 2 parallel flat surfaces in the lathe by facing off with the work across the chuck proved to be the killer blow and I ended up with this.

I decided the best thing was to have a few beers, sleep on it and try a different approach tomorrow.

Second time round I thought I'd try to machine the 2 parallel faces first (after truing the diameter and facing the ends). The first face seemed to look ok, visually at least.

I took far more time and care aligning the work this time, whilst saying to myself 1000 times 'I must not leave my parallels in the chuck'.

First impressions suggest 2nd face looks ok.

Yesterdays bodged attempt came in useful as a temporary threaded arbour to hold the work whilst I finish turned the diameter, cut a few decorative grooves and cut a taper for the top.

I also decided at this point to drill a small oil hole from the top to meet the axle hole. I'm not sure this will be necessary but it will give an excuse to top it off with a small knurled nut which will be a bit of added decoration if nothing else.

It's not perfect but I'm happy with the result.

Not yet fixed down and there is still a bit to come off the crank pin and axle but it's beginning to take shape.

Peter.