I have two copies of Tubal Cain's "Model Engineers Handbook", one by my desk, one in the workshop, so I guess it would be my first recommendation

Brian

Neil is too modest to recommend his own 'The Mini-lathe' so I will. I'd also recommend 'The Amateur's Lathe' by Sparey.

For reference, Tubal Cain's 'Model Engineer's Handbook' is succinct. Machinery's Handbook covers much more!

Although the books above answer many questions, they also open the door to many more. Much depends on where your interests take you – Sheet Metal, Castings, Clocks, Welding… Fortunately there are plenty of good books available.

Not all are equally on target, but I find the Workshop Practice Series good for specific subjects.

Also have a look at the Camden Website – they stock a very wide range of engineering related books. Most are in the Engineering Practice and Skills section, but Technical Steam, Horology, Electrical, Foundry, Hot Air Engines and other sections also have gems.

Dave

+ 1 for Tubal Cain's book.

Although written when the Myford ML7 was the most populous lathe, Sparey's "The Amateur's Lathe" is a good starting point, followed by Bradley's "The Amateur's Workshop". "The Myford Series 7 Manual" is specific, but contains information that is useful elsewhere. After that you are into books from the "Workshop Practice Series", for more specific activities, such as Soldering and Brazing, Taps and Dies, Workshop Hints and Tips, Making Small Workshop Tools, Screwcuttiing in the Lathe, and when you are more experienced and confident; Milling, or Gearcutting.

The books by Neil Wyatt and Dave Fenner deal with the mini lathe, but the techniques and principles, if not the specifics, can be read across onto other machines.

If you want to get into screwcutting, Brian Wood's "Gearing of Lathes for Screwcutting" can be a good source of information, so that you grasp the principles involved.

Plus, you will always have a crowd of folk on here who will be happy to give advice, and even practical help.

Howard

The first book I bought (many years ago now) and found very useful was Using The Small Lathe by L C Mason. It takes the new lathe owner through all the turning methods likely to be needed. Very readable and superbly informative.

Also +1 for 'The Amateur's Lathe' by L h Sparey especially f you intend buying a Myford lathe.

.As you gain experience try The Model Engineer's Workshop Manual by G H Thomas.

Good luck

Eric

To gain an appreciation of what can be done at home with very little, I'd recommend the David Gingery series 'Build your own Metalworking Shop from Scrap' here: **LINK**

You don't need to make any of the machines, just learn the thought processes and get a feel for it all. It's a complete industrial revolution in one bound volume.

Regards

Richard.

.

One of you needs to start by sending a personal message to the other

[assuming that you are logged-in] You will see a 'Message member' link at the bottom-left of any previous post.

MichaelG.

'The Amateur's Lathe' by Sparey.

+1

Was the bible for me starting out

Returning to model engineering after a gap of nearly 45 years has really brought home to me the need fir an up to date readable book on modern techniques. Reading through the posts I suspect I am not alone in this.

Topics that I think need to be in an updated book, even since I modelled in the 1970s, could include:

Metrification, DROs, 3D printing, tig and mig welding, the ready availability of machines, not so Myford focussed as in the past, invertors, no blowlamps or air/towngas, disappearance of one-off foundries, new materials like plastics, laser cutting and changes to boiler codes and soldering materials.

And I have no doubt many more could be added!

Apart from books about model engineering, Tubal Cain’s reference book is essential as a source of information, but I have to admit it is not really a bedtime read!

Edited By Nick Clarke 3 on 12/08/2018 21:29:30

I quite agree Andrew – originally I included it but lost my post through operator error before I uploaded it and missed it when reposting.

Incidentally I used to work with a teacher of technical drawing who claimed to teach from resources in a filing cabinet, none newer than 25 years old. At least with CNC & CAD that is unlikely to happen!

Edited By Nick Clarke 3 on 12/08/2018 22:01:22

Dunno about 3d printing as I only have experience of my own machine, but I was teaching CNC in school in g code using a small CNC lathe attached to a BBC computer in the late 1980s

+1, concur.

But i would add the two American channels Abom79 and Keith Fenner's Turnwright machining. Both always very interesting.