Brass I beam

Advert

New Replies

Report Bug

Help/FAQs

Brass I beam

This topic has 10 replies, 9 voices, and was last updated 24 December 2022 at 14:28 by Dave Smith 14.

Viewing 11 posts - 1 through 11 (of 11 total)

Author

Posts
23 December 2022 at 18:03 #30260
Boiler Bri
Participant
@boilerbri
Advert

23 December 2022 at 18:03 #625953
Boiler Bri
Participant
@boilerbri
Does anyone know where to source 1.2mt long 20mm x 10mm I beam in Brass?

Bri
23 December 2022 at 18:05 #625954
File Handle
Participant
@filehandle
Curious of its intended use?
23 December 2022 at 18:18 #625956
JasonB
Moderator
@jasonb
Eileen's Emporium do some brass sections but their site is down for maintenance at the moment so can't check sizes as your need may be a bit large.

is soldering Tee section together an option?
23 December 2022 at 18:19 #625957
DiogenesII
Participant
@diogenesii
?Curtain track – though uncertain if you will get the right dimensions, you might get close…

Hunter & Hyland might be 8.5×19..

Edited By DiogenesII on 23/12/2022 18:23:07
23 December 2022 at 19:01 #625959
John Beresford
Participant
@johnberesford27902
I believe Eileens Emporium have sadly ceased trading as of this month. They will be sadly missed!
23 December 2022 at 19:11 #625961
Nigel Graham 2
Participant
@nigelgraham2
I think curtain track is not symmetrical, at least not the ones I have seen.

Is the 1200mm the full length of the finished item or the total stock requirement?

If the finished work is lots of short pieces, and depending on exterior appearance, it may be possible to make each piece by slitting a length of square tube into two and soldering them back-to-back. Or better, if available, brass channel of appropriate size.

Distortion might be a problem though, unless heated very evenly.

I used something like that principle to make the H-section beam front axle for my steam wagon, but that is of larger section, steel, and welded. The stock was folded channel.
23 December 2022 at 19:29 #625965
Boiler Bri
Participant
@boilerbri
It’s not actually for me. A friend is making a Norfolk Wherry and he needs it in the length.

If it had been shorter I could have made it up but he really needs the length.

Thank you for the replies. I will investigate them all.

Bri
23 December 2022 at 19:41 #625968
peak4
Participant
@peak4
Posted by John Beresford on 23/12/2022 19:01:05:

I believe Eileens Emporium have sadly ceased trading as of this month. They will be sadly missed!

According to Facebook, that appears to be the case, but I've no confirmation
https://www.facebook.com/Eileensemporium/

Bill
23 December 2022 at 20:29 #625971
DC31k
Participant
@dc31k
Posted by Boiler Bri on 23/12/2022 19:29:09:

If it had been shorter I could have made it up but he really needs the length.

What is preventing you making it in that length?

If it is the travel on your machine not being long enough, some creative fixturing that allows you to cut a section, slide it along and then cut another section will overcome that.

As it is brass, it can be cut with a 6mm or 1/4" carbide end mill held in a trim router. For the authentic rolled section look, use one with a corner radius.
24 December 2022 at 14:28 #626033
Dave Smith 14
Participant
@davesmith14
Very Sadly Eileens Emporium have gone into administration. This was posted on a number of modelling associated websites on December 11th.

I am very sorry to have to tell you that Russan Limited, trading as Eileens Emporium has ceased trading and appointed liquidators.We have done our best to send out all the stock we have for pre-paid orders. I am sorry that we were not able to complete all of them.

Any clains against the business should be sent to:

Christine Vaines, Begbies Traynor, Suite C 11 Kingsmead Square, Bath, BA1 2AB | T: 01225 316 040 | Email Christine.Vaines@btguk.com
Author

Posts