Neil,

You should be able to work out the valve acceleration from the cam profile and max engine speed. From this, together with the weight of the valve components you can work out the force required to counteract the kinetic energy of the valve gear and keep it in contact the cam.

So much for the theory. In practise you can compare it with other similar designs. What is the capacity of your single? As a start, the 10cc Matador OHV uses a 4 turns of 22 swg 1/4" OD and 3/8" long. My own design 10cc side valve, which a has a more aggresive cam than the Matador uses 5 turns of 22swg with an ID of 1/4" and 0.6" long. Both of these seem to work fine in my experience up to 10,000 rpm.

I can also let you have copies of the missing instalments if you wish.

cheers,

Rod

Edited By Roderick Jenkins on 13/01/2013 20:19:06

A crude measurement with a spring balance shows about 3 1/2 lbs to open the Matador valves.

Looking at my Mastiff book, Len Mason used 22swg 1/2" long, 6.5 turns and 7/32" ID. This for a four cylinder 24cc . I've got the drawing for ETW's Kinglet: no mention of valves springs on that either- in fact the drawing leaves quite a lot to the imagination.

cheers,

Rod

Had an idea it might help, so I looked at Edgar T. Westbury's book "Model Petrol Engines", but there is no mention of the specs for valve springs on any of the engines, Ooh well its a nice wee book, does'nt tell too much about building, but it gives some ideas. Ian S C

I've been whiling away the progression of a never ending cold by reading my newly acquired ME backnumbers. In April 1945 ETW tells us that the springs for his 15cc Kiwi are: 18SWG, 5/16" ID, 6 coils in 3/4".  He gives the impression that these were just a best guess but they seem to work.  I'm a bit surprised because he usually got Dennis Chaddock to do hisdifficult sums.

Rod

Edited By Roderick Jenkins on 16/01/2013 22:10:23

(1)

*I've been whiling away the progression of a never ending cold by reading my newly acquired ME backnumbers. In April 1945 ETW tells us that the springs for his 15cc Kiwi are: 18SWG, 5/16" ID, 6 coils in 3/4". He gives the impression that these were just a best guess but they seem to work. I'm a bit surprised because he usually got Dennis Chaddock to do hisdifficult sums.*

"I am often severely rapped by readers for neglecting to give details of valve springs, but it is difficult to specify essential dimensions, because ultimate strength and durability depend on several factors, including not only the quality and temper of the spring steel, but also the pre-stressing of the material in manufacture. For the best results, some experiment is called for; the springs which have been found satrsfactory are 3/4 in. free length, 5/16 in. outside diameter, by 20 s.w.g., with six complete turns, not including the flattened end turns."

A surprisingly large number of older people at the place that I was trained and worked years ago knew Westbury well and some even counted him as a personal friend . They had come to know him in three separate ways :

Through his collaboration and lifelong friendship with Whittle .

Via studies at Cranwell .

Via Model Engineering .

Whittle was a frequent visitor to my workplace and these visits continued into my time though sadly I never met him . He apparently had great respect for Westbury and often talked happily about his early jet engine days and the help and support that he got from him .

In their earliest days they had built and flown ic engine powered model aircraft where every single part was designed or made by one or other of them .

Whittle was well trained as an Artificer and had I believe a Higher Technical Certificate – not a bad qualifcation to have achieved pre war .

Those people that knew Westbury described him as quiet and reserved in his ways but with an immense wealth of technical and historical knowledge .

I never met Westbury but I did meet Chaddock several times . I would say that as an all round engineer Westbury outclassed Chaddock considerably .

(2) I've never liked the term Great Expert as used so freely in the Model Engineering world . In truth many of the much praised regular contributors to ME have been barely competent and some at least have been complete idiots .

There have been some excellent regular contributors – Westbury , Duplex and a few others over the years . What makes me sad though is that many of the real experts in Model Engineering don't often write articles and are quite unknown to the general public .

One of these unknown experts was the late Eric Grifiths of Bristol . Older members of Bristol SME will remember him as will people who worked in AMD . He was a true Mechanical Engineer who could turn his hand to anything and almost always achieve success .

We got on well and had frequent long talks . Like me his work and hobby had long since merged – professional workplace and home workshop were just extensions of one another !

Perhaps some people that knew him could tell us more about his activities .

In those early days of mine in industry there were lots of people in Engineering companies interested in Model Engineering . The interchange of ideas between model engineering and full size work was sometimes fruitful – I can't tell you specifics but several difficult design problems in Pegasus , Olympus and RB199 engines were solved by Model Engineers in their home workshops !

It was fair exchange – many a large model engine casting was machined in the tool room .

Regards ,

Michael Williams .

We won't ever know who the great model engineers are if they don't put their head above the parapet. I think there are Great Experts and they are the ones who have offered us the benefit of their knowledge by writing for ME. With his style, designs and plain good sense I think ETW was the greatest, surpassing LBSC because ETW told us much of the work and reasoning behind his offerings (and by admitting that there was no definitive to the size of valve springs!). ETW was clearly also respected by his more academic peers; Chaddock and Nevil Shute who clearly, in his patrician way, partly based his hero in "Trustee from the toolroom" on ETW. In my opinion only Tubal Cain has come close to having the same authority on his subject.

cheers,

Rod