Michael Cox Tangential Tool Holder- MEW 179

Advert

Michael Cox Tangential Tool Holder- MEW 179

Home Forums Workshop Tools and Tooling Michael Cox Tangential Tool Holder- MEW 179

Viewing 25 posts - 1 through 25 (of 41 total)
  • Author
    Posts
  • #73718
    michael howarth 1
    Participant
      @michaelhowarth1
      I made a tangential toolholder as described by Michael Cox in MEW 179, over the weekend. The toolholder performs well and eliminates most of the chatter that I get on my light lathe. It also gives 40 thou cuts with no problem, an excellent finish and is recommended.
       
      However, a strange thing did happen that I hope someone can throw some light upon. I had taken the toolbit out of the holder to hone it but when I replaced it, I inadvertently put it in upside down – it was getting late and I should have gone to Specsavers long ago – which meant that the cutting edge exposed was just the slanting cut that one usually gets on HSS bits. It cut exceptionally well – probably as well as the properly ground toolbit. That is not the end of the tale however, because when I realised that the cutting edge looked the wrong shape I compounded the error by turning it through 90 degrees so that the cutter had a positive side rake and cut again. The result was an incredibly fine finish although the depth of cut was limited to about 10 thou.
       
      Whatever the explanation I am inclined to make another holder so that I have one to hand for roughing and one for that finish
      Advert
      #16694
      michael howarth 1
      Participant
        @michaelhowarth1
        #73719
        mick
        Participant
          @mick65121
          The ground angled face on HSS tool bits was always intended to be a front clearance angle to save you grinding one on, at least thats what I was told by my instructer, although I’ve always thought it to be too much, as 8 to 10 degrees is considered to be about right. The more top rake you apply to a finishing tool, the better the surface finish, so if your tool bit’s rake angle is indeed the front angle, this might explain it, as all the cutting edges are in fact factory ground, which is a far smoother edge that most workshop regrinds can produce.
          #73721
          Michael Cox 1
          Participant
            @michaelcox1
            Glad you like the toolholder. Thanks for the interesting comments regarding the orientation of the toolbit. I will make some trials myself when I get time to understand what is going on.
            Mike
            #73722
            chris stephens
            Participant
              @chrisstephens63393
              Hi Mick H,
              Welcome to the wonderful world of tangential tooling, good aren’t they.
               
              You might find that honing a tangential tool bit to be a waste of time, as they seem to work better when used straight from the grindstone, provided that your stone is not too coarse, of course. I have tried using a diamond wheel on the Quorn in the hope of an even better cut and was disappointed, and I believe I am not alone in this conclusion.
               
              I don’t know which sharpening jig you are using but the 30 degree “V” block gives a better cutting tool than the commercial variety, it’s all a question of which way the grinding striations run. The commercial jig is very good for sharpening thread cutting tools. The two items are at the bottom of the picture are the two styles of jig.
               
               
              You might find that by putting a radius of about 0.4mm on the toolbit gives a very good finish and can also be used for roughing, it also reduces sharp corners that can cause problems in some situations.
              chriStephens
              #73727
              ady
              Participant
                @ady
                I used to do a lot of experimentation.
                 
                The best cut I ever got was the toolbit pointing upwards 45 degrees from the back.
                The swarf dropped off while it lasted, it diverted the steel like it was wood shavings.
                Very difficult and fiddly to set up and replicate though, I gave up on it eventually.
                 
                For boring I use “self sharpening tooling”
                If I cut upside down on the far side again, and cut slightly above centre height.
                The tool squeaks slightly and “lasts forever” as the cutting edge and the hss material below the cutting edge(above actually, because it’s upside down) is ground away by the workpiece, very handy for roughing out a big bore.
                 
                The books tend to give you the basics but there’s a lot they don’t bother getting into because production line techniques are only about established practices.
                 
                The smaller the angle used to remove metal the less work required to do the task, less heat, less wear and tear etc, but harder to lose heat if it’s too acute, and can’t do bigger cuts
                fascinating stuff.

                Edited By ady on 22/08/2011 20:57:12

                #73740
                michael howarth 1
                Participant
                  @michaelhowarth1
                  Mike Cox, yes I am very pleased with the holder. I made it from half a G clamp which was past it’s best, which I picked up from a car boot sale for about 20P. It saved me having to chomp through half inch mild steel…and I’ve still got the other half to make another one.
                   
                  I do find it quite bizarre that I can put a tool in upside down and back to front so that there is positive side rake and still get a finish as good as any I have ever managed to achieve with conventional tooling! I suppose that is part of what Chris calls calls a wonderful world and Ady calls fascinating stuff!
                   
                  Chris asks what sort of sharpening jig I am using, but the answer is, I haven’t made one yet……I shall no doubt have to do so, but as I say above, initial results did not make it a priority.
                  #73744
                  Martin W
                  Participant
                    @martinw
                    Hi
                     
                    I also made one of these just to see if there were any benefits from using a tangential tool system. My experience reflects that of others in so much that it was easy to obtain a good finish on all materials I tried. The only draw back with Michael C’s design is that the tool securing screws can get in the way if taking a deep cut up to an edge. Other than that, the tools sharpening is simple especially as I already had a piece of steel with a 90 deg slot cut in it. Angle it approximately and slide the tool bit to the grind wheel and the jobs done.
                     
                    I tried rounding the tool tip profile to see if I could get an even better finish but the results were variable and on steel seemed to generate much more heat even after honing the tip, cutting edge set true to turning centre. I have probably upset the geometry some where so will re-grind to a fine tip and try again when time permits.
                     
                    Overall it is easy to make, simple to sharpen and cheap to run; what more could anyone ask for from a bit of kit.
                     
                     
                    Cheers
                     
                    Martin
                    #73745
                    jomac
                    Participant
                      @jomac

                      Hi. same subject, different material. Iv’e got in my workshop a 2 meter long wood lathe, cause besides bowls,newel posts,etc etc, I also made and sold snooker cues, one of the flat HSS tools is 800mm long, it has a 30mm wide and 10mm thick blade, the straight edge of the tool is angled about 15 degrees and a wedge shaped cutting edge. If I place the tool tip on the work at about 35 degrees lower the tool so that the heel touches the work then slowly lift the handle up the tool starts to cut, Because the angle of the cutting edge is now about 15 degree to the vertical, I can cut very very thin shavings and dust. ( the finish is perfect and does not need sanding} now if I turn the tool tip so that the angle is 30 degrees I can take deeper cuts, that if you are not careful can result in a rippled affect. and some times a dig in. OK think about it,?????, When using my home made tangental tool, with 1/4″ round I get a good finish, some times better than the square tool, if I turn the tool clockwise (as seen from the top) lift the tool slightly, so that the cutting edge is on the center line, its like my wood turning chisel. Ultra fine shavings/chips, and the angle of the cutting edge is near vertical. So play around with you settings, until you arrive at a good compromise. Its interesting and fun just experimenting.

                      John Holloway.

                      #73751
                      ady
                      Participant
                        @ady
                        The best basic setting cutting tool I have, came attached to something I bought (can’t remember now)
                        It does a great job.
                         

                        #73757
                        jomac
                        Participant
                          @jomac

                          Chris Hi, nice looking toolholder, very proffesional gear. When I made my toolholder I offset the front by 15 degrees, as my mill was out of order I grooved and welded up the parts, next one I will machine on the mill, (when I get time) take photos and try to add to posts (not really conversant with that at the moment). Any way when testing out the tool, I was taking off 4mm in one pass, which is not bad for my Hercus, (South Bend style) then I upped the ante and found that the toolbit was dropping under the increased pressure, so I drilled and tapped the holder to take 2, 6mm, cap screws, since then Iv’e had no problems. As I said in previous post, rotating the round tool bit clockwise, and then raising it a bit so that the side of the bit is at center line, it acts like my woodworking chisel, ie the front of the tool is nearly rubbing on the work, thus NO dig in’s, try it and let us know if you have any problems, I might have been just lucky.

                          John Holloway

                          #73759
                          John McNamara
                          Participant
                            @johnmcnamara74883
                            Hi All
                            HI Jomac from Jmac. And I notice you did something similar with wood.
                            A while back with my old lathe a Colchester plain bearings, flat belt drive and no gearbox just change gears model dating from the 40’s. I experimented with a shearing rather than a cutting tool. The old lathe was a bit past its prime and the maximum speed was rather low. I wanted a fine finish. I had read of shearing tools.

                            Imagine grinding a flat chisel point right across the cutting edge of a HSS tool; to clarify at 90 degrees to the length of the tool, as if you were making a wide parting or grooving tool. The tool did have top rake and clearance for steel.

                            Now the interesting part:
                            Rotate the tool so that the cutting edge is at almost but not quite 90 degrees (Almost vertical). As the work rotates the cutting edge is lead into the work, the swarf was quite different to normal, coming off as thin slivers that formed a sort of thread. Like very fine steel wool, soft to the touch.

                            If you think about the geometry of the setup; the actual cutting area was only in the centre of the tool where the radius of the work piece contacted the centre of the chisel edge.

                            Using this method the long axis of the HSS tool bit itself is at 90 degrees to the work both horizontally and vertically and it is fed straight in. The rotation of the cutting edge to the work and its relief angles are the only variables. 
                            A very fine finish resulted. I was only removing very small amounts of material maybe .001 to .003 at a time.

                            Reading this thread reminded me of the experiments. At the time I used square inserts, this required grinding the very fine angle. It would be interesting to use a piece of round HSS and vary the cutting/shearing/scraping angle (I joined them together because there is a bit of everything in this setup.)

                             
                            Has anyone else in this place read of or experimented with similar tools?

                            Cheers
                            John

                            Edited By John McNamara on 23/08/2011 13:54:42

                            Edited By John McNamara on 23/08/2011 14:13:02

                            #73762
                            John McNamara
                            Participant
                              @johnmcnamara74883
                              Hi All

                              I did a bit of googling using

                               
                               
                              Others have been doing research too.
                               
                              Cheers
                              John
                               
                               
                              #73771
                              chris stephens
                              Participant
                                @chrisstephens63393
                                Hi to the two Johns
                                If you raise the tool bit a touch above centre height, and cut backwards, you get a shearing cut which will give a very good finish. In fact if you make a cut in the normal way and then cut backwards, without withdrawing the tool, on the penultimate cut and measure then take the final cut again cutting backwards afterwards, you will get a more accurate cut. What happens is that on the back cuts you take any spring out of the tool in a consistent way. Readers who have Shaublin or Hardinge lathes can ignore this recommendation but for us mortals it is worth giving a go.
                                 
                                Back in the fifties there was a small article in ME about making a shearing cut tool. The tool was very much like a “D” bit, but instead of the flat being in line with the axis there were a few degrees of positive rack. The tool in use was turned in the tool post so the cutting edge was anywhere between the 1 & 2 o’clock position. The recommended depth of cut was given as about 1 thou and then it will give shavings like fine wire wool.
                                 
                                If any of you chaps reading this wonder why a good finish appears to be of so much interest, well you can’t accurately measure a rough surface as you can only measure over the peaks, which will soon wear down in use.
                                 
                                chriStephens
                                #73772
                                John McNamara
                                Participant
                                  @johnmcnamara74883
                                  Hi All
                                   
                                  It looks like GMTA….
                                   
                                  Link here:
                                   
                                   
                                  Cheers
                                  John
                                  #73781
                                  chris stephens
                                  Participant
                                    @chrisstephens63393
                                    Hi John,
                                    The one I was describing is the same as at the bottom of the second link.
                                    I would have posted a copy of the ME article but I did not want to upset the “keeper of the blue pencil” even more than I seem to have done already in recent times.
                                    chriStephens
                                    #73786
                                    chris stephens
                                    Participant
                                      @chrisstephens63393
                                      Hi Martin,
                                      To over come your problem, can you lower the tool holder and then raise the cutting tool, this will give you a touch more side clearance.
                                      chriStephens
                                      #74339
                                      michael howarth 1
                                      Participant
                                        @michaelhowarth1
                                        I have delayed making the grinding jig for Mike Cox’s toolholder because my freehand efforts have been pretty successful. I am now ready to do the job properly but having reread the article, I cannot find any reference to the angle of the channel in the grinding jig. From the photos it looks as if it is about 60 degrees. If that is the case, then it occurs to me that there are three ways that the toolbit could be held in the jig. ie one side of toolbit against the left side of the channel, one side of the toolbit against the right side of the channel or the 90 degree angle of the toolbit centred over the centre of the channel. If the angle of the channel is 90 degrees then of course there is only one option.
                                         
                                        I wonder whether Mike or someone more in tune than I am can assist with this. I hope the verbage above is reasonably clear. I did draw a diagram but I can’t seem to attach it.
                                        #74342
                                        John McNamara
                                        Participant
                                          @johnmcnamara74883
                                          Hi Mick H

                                          There is another way to attach a photo, use a free file sharing site. I use a site called Mediafire. Once you have posted a file there, copy the link URL by pressing the copy button in Mediafire and then move to the MEW “Post a reply” window and click the image icon at the top (second from the right, like 2 blue hills with a sun above); a window will pop up asking for the URL…You already have it on the clipboard so just right click paste it in and close the window. Done…It will appear in a few seconds.

                                          There are many other free sites. I chose this one because at the time it looked OK, that was about 6 months ago…I still use it. It is also handy for making large files that you cannot email available to friends. Just upload and send them the link to download it. Files are not made public. The only access is via the link, you control who you give it to. (You can also share entire folders of files, great for family photos)

                                          The make their money from the advertising on the pages. Annoying but they have to eat. There is a paid account as well then there is no advertising and you get an even bigger file quota….
                                          There are a lot of sites offering similar services, have a look around the web.

                                          Cheers
                                          John

                                          See screenshot below use the “direct link” selection.

                                           
                                          For those wondering how I grabbed the screenshot and put the red arrows on it? I used “Snagit”…easy to find on Google. I cannot recommend Snagit too highly. It has made copying , snipping and marking up a pleasure instead of a chore.
                                           
                                          All you do is press The print screen button on your keyboard, drag a box arount the part you want and click, it will pop up in a window yo can edit with arrows etc, or comments then press save and it is ready as a JPG file. or press copy and you can paste it directly in an email. 
                                           

                                          Edited By John McNamara on 02/09/2011 09:18:57

                                          #74344
                                          michael howarth 1
                                          Participant
                                            @michaelhowarth1

                                            Thanks for the tip John, I shall download it later…..the problem that I have though is that when I click on the “hills and sun” icon, the screen goes a sort of pale blue and freezes. I am not much good in the workshop…..even worse on computers. I think that I am in the wrong century.

                                            #74345
                                            Gary Wooding
                                            Participant
                                              @garywooding25363

                                              Is this what you wanted?

                                               
                                              #74347
                                              michael howarth 1
                                              Participant
                                                @michaelhowarth1

                                                Gary, thanks….it certainly looks like another way of doing the same job, but the jig that Mike Cox describes looks more like the one on the left, in the photo posted by Chris Stephens on 22nd August.

                                                Edited By mick H on 02/09/2011 10:03:27

                                                #74364
                                                chris stephens
                                                Participant
                                                  @chrisstephens63393
                                                  Hi Mick H,
                                                  Cox’s jig is set at 30 /60 degrees and the tool bit that is to be sharpened is placed with the long corner downwards. The jig is used with the trough pointing downwards at the wheel so that the tool bit is trailing, short corner to long corner. If you get worried that your fingernails are getting close to the wheel, some find a simple screwed down tool bit clamp useful.
                                                  For general purpose use the V jig is superior to the jig in the previous post, which will work best with the the Oz style tool, as it is intended more for cutting in one direction only. As I have said before the striations favour one edge only , but the V one favours both cutting edges, so will also cut equally well on the back cut and when facing.
                                                   
                                                  When your screen goes blue, scroll up to the top of the page where you will find a box where you can insert details for your insertions. It is also the place where you can find little smiley faces.
                                                  chriStephens
                                                   
                                                  #74365
                                                  John Coates
                                                  Participant
                                                    @johncoates48577
                                                    Posted by Gary Wooding on 02/09/2011 09:33:22:

                                                    Is this what you wanted?

                                                     
                                                     
                                                    Gary
                                                     
                                                    Thanks for this. I can now make it and get my tool steel correctly ground
                                                     
                                                    John
                                                    #74366
                                                    Gary Wooding
                                                    Participant
                                                      @garywooding25363
                                                      Posted by chris stephens on 02/09/2011 12:16:07:
                                                      For general purpose use the V jig is superior to the jig in the previous post, which will work best with the the Oz style tool, as it is intended more for cutting in one direction only. As I have said before the striations favour one edge only , but the V one favours both cutting edges, so will also cut equally well on the back cut and when facing.
                                                       
                                                      With the V-jig the striations are the same for both cutting edges, but, since neither are perpendicular to a cutting edge, both are less than ideal.
                                                      Well, that’s how it seems to me.
                                                      I don’t have an axe to grind about this; I simply worked the angles out for the Oz style jig, which seemed to be rather easier to make than the V one. It certainly seems to work OK.
                                                       
                                                      Gary
                                                       
                                                    Viewing 25 posts - 1 through 25 (of 41 total)
                                                    • Please log in to reply to this topic. Registering is free and easy using the links on the menu at the top of this page.

                                                    Advert

                                                    Latest Replies

                                                    Viewing 25 topics - 1 through 25 (of 25 total)
                                                    Viewing 25 topics - 1 through 25 (of 25 total)

                                                    View full reply list.

                                                    Advert

                                                    Newsletter Sign-up