Hi Danny M2Z

Kwil Is right Bacterial action can be a problem, It will rust steel and get very stinky if left in a sump or tray. If you keep your slides nicely oiled that "tramp" oil can hitch a ride and cover the soluble oil in the sump forming a thin film sitting on top of the water emulsion keeping the air away from the soluble oil, an ideal environment for anaerobic (without air) bacteria to form…. very stinky.

Also If you leave a vice on the table watch out for a nasty stain under it when you remove it.

You may wish to have a look through a second hand machinery website, notice the paint has been removed from around the machine, often right down the front of the machine. No not flying chips they cannot reach many of the areas you will see, just the paint being dissolved away.

In my workshop I only use pumped coolant on a large old vertical mill, milling generates a lot of heat and cutters are not cheap coolant makes them last a lot longer, it has a sump in the cast iron base and yes if I have not used it for a while the sump can become a bit of a science experiment. My lathe does have coolant but I prefer to just dab it on when needed. The sump is empty.

Not wishing to be negative but a few people have an allergic reaction to oil and or cutting oil, they can cause dermatitis or other maladies, most people are OK I have no problems, but best keep your hands clean, just in case

Regards
John

Soluble oil certainly spoiled the appearance of bed of my (then) new Myford ML7 before I realised what was happening. The bed wiper felt left some nasty pock marks which continued to annoy me until I disposed of the lathe quite recently. On my new lathe, I only use neat cutting oil (eg Warco Neatcut) but I dilute it 50:50 with paraffin.

Andrew M

Danny,

I believe you are quite right to have some concerns. You obviously realise that the main problem with this product is that the oil never ACTUALLY combines with the water , but rather it lies in suspension, and therein is the nub of the conundrum . I also have experienced staining on the slideways on my then newly factory reconditioned Myford. The stains were quickly removed by stoning and the coolant system changed to oil , a decision I have never regreted . I do however continue to use soluable oil on my Kennedy power hacksaw where it is perfectly suitable , principaly because it is totally free draining and is regulalry maintained. Please also be aware that use of soluable oil also brings with it some very real risks associated with Legionellea , particulalry where intermittant usage is envisaged and as briefly refered to in my post of 21/01/2013 under the thread of "Cheap coolant system for a mini-mill ".

Trevor.

I feel I should add a few lines on the subject of coolant/lubricants for machining based on my own work on the chemistry of these.

Not all maching fluids are alike. There are a multitude of formulations out there. Of course some are only available as 200 litre drums and so rarely accessible to the small user.

Firstly neat oils, these have the much longer history and are well understood for their designed purposes. They are the only type to perform well on grinding machines. Surface grinders are very sensitive to the type used.

Secondly so-called suds,these are not actually soluble oils, but often an oil-in-water emulsion, sometimes water-in-oil. Many more formulations exist especially over the last 10 years or so as chemists look at ways of overcoming the deterioration of mixed fluid in the tank. Other problems associated with these fluids are, as mentioned in earlier posts, staining of metal surfaces and most drastic of all, health problems which develop as the fluid ages.

Those health problems can be severe, in one large Midlands plant, now closed, a high proportion of the workforce developed lung problems which lead to the intervention of HSE and was attributed to poor fluid maintenance. There is guidance available **LINK**. and also **LINK** which points to specifics.

There are recently available fluids supplied as concentrates for mixing with water which have shown experimentally and in small and mid-scale practice to be less prone to deterioration.

As this is a topic in which I have a special interest may I ask contributors to be more specific when referring to the fluids they use and the problems which they experience.

Thank you

JerryNotts

I guess adding Domestos would be a bad idea because of the chlorine content. How about a UV light in the pipe? Another traditional bactericide is copper – dunk you copper turnings in the tank?

Does slathering the underside of the vice with grease seal out the fluid or does the fluid disolve it too readily.

I have been using pumped NEATCUT oil for several months now for lathe and milling machine because I have an uninsulated workshop and the theory was that it would anoint everything and stop my kit rusting. It sure does that very well.

In addition, there is no risk of finding the coolant tank frozen solid after a cold night, no risk of stenchy bacterial reactions and it has virtually no smell.

Disadvantages are: I need to wait overnight before removing swarf from machines to give it chance to drain. I wear BODYGUARD nitrile gloves at all times as I don't feel it a good idea to be in regular contact with the stuff. and finally – its messy – no two ways about it. However, I prefer a bit of messiness to rusting machines and tooling.

Andrew M – isn't that cocktail of paraffin and oil a bit smelly? Maybe if you are only brushing it on its not so bad.

As for mystics causing staining :

Take a brand new Jones & Shipman (say) surface grinder and use it daily (during the working week of course) with mystic for two years. Then detach the magnetic chuck for the first time since new from the bed. Staining? Thick rust more like!!!

The best mystic I ever used on a grinder was supplied by Cincinnati Milacron. When mixed it looked just like water with a slight bluish tinge – really good stuff. The worse was used in a large, little used universal grinder in a dark corner of the factory. This stuff was yellow, milky and stunk like a mixture of rancid cheese, stale sweat and mildew – a bit like a politician I 'spose!

Rik

Edited By Rik Shaw on 16/10/2013 18:03:40

Many years ago I knew a guy who had worked at Porton Down – not on germ warfare, but on the bacteria living on the oil/water interface in big storage tanks. Apparently the gas they generated caused no end of issues.

Neil