Schedule of the TB6560-V2 stepper control card

Advert

New Replies

Report Bug

Help/FAQs

Schedule of the TB6560-V2 stepper control card

This topic has 17 replies, 6 voices, and was last updated 1 April 2013 at 16:48 by Royston.

Viewing 18 posts - 1 through 18 (of 18 total)

Author

Posts
20 February 2013 at 18:50 #112679
Svarven
Participant
@svarven
Hi
Have come across a stepper motor driver cards, TB6560-V2, a red card.
I need now is a schedule on the coupling of motors, PC and hand control.
Have searched on Google but only found diagrams of the blue card.

Is there anyone here who has a schedule?

Bertil
Advert

20 February 2013 at 18:50 #15000
Svarven
Participant
@svarven
20 February 2013 at 19:43 #112685
John Stevenson 1
Participant
@johnstevenson1
Bertil,

Sorry but saying red card is not specif enought.

There are two cards out there, both with the TB6560 chips on and both red.

One has just a single parallel port socket and one has the parallel port socket with a serial port to the side of it.

Both red but both different animals. Any chance of a picture or link ?

If you haven't bought this then a word of warning to only operate these at 20 to 24 volts MAX as they easily burn out. they are not the best cards on the market.
20 February 2013 at 20:12 #112689
Svarven
Participant
@svarven
This is the controller card.
20 February 2013 at 20:57 #112696
Svarven
Participant
@svarven
20 February 2013 at 21:41 #112701
John Stevenson 1
Participant
@johnstevenson1
OK, Mine came with a CD with the wiring on it.

need to look it out tomorrow.
21 February 2013 at 00:00 #112705
Chris Shelton
Participant
@chrisshelton11794
Here is a link to a website showing connection details.

http://whatisacnc.com/driver-board/tb6560/

HTH
21 February 2013 at 16:56 #112738
Svarven
Participant
@svarven
Thanks
It solved the problem with the connection to the PC.
But I also need to know the configuration of the 15 pin connector and DIP switches
21 February 2013 at 17:10 #112739
Les Jones 1
Participant
@lesjones1
Hi Svarven,
That information seems to be in the link Chris Shelton gave you under setting up the tb6560

Les.
21 February 2013 at 17:27 #112740
Svarven
Participant
@svarven
I must be blind, because I just only find scematics for the blue card at that link.

(or my bad english)
21 February 2013 at 17:37 #112742
Les Jones 1
Participant
@lesjones1
Hi Svarven,
This is Chris's link which shows you a link to here.

Sorry Svarven, This information is for the blue board not the red board which you require.

Les.

Edited By Les Jones 1 on 21/02/2013 17:51:38
21 February 2013 at 20:14 #112748
Svarven
Participant
@svarven
Yes but that is not the same card. See my pic above.

Maybee its the same configuration of the 15 pin, but im must be sure.
27 February 2013 at 18:07 #113274
Svarven
Participant
@svarven
John S have you looked at you cd?

Bertil
27 February 2013 at 19:01 #113280
John Stevenson 1
Participant
@johnstevenson1
Yes, can't find it but looking inside the tiny drag engraver it's fitted to it's not a red board anyway.

Have you tried emailing the seller of the red board on ebay for a manual, they usually will give you a link prior to purchase
27 February 2013 at 20:27 #113294
Svarven
Participant
@svarven
Yes John i have , but have not get any answer from the seller.

Bertil
19 March 2013 at 22:38 #114800
Olaf
Participant
@olaf
Hello,
i do own the same red Controller card TB6560 V2 as on the picture from Svarven. And i do need some more information too (DIP Switches, PINOUT).
Do anyone hase any further Informations about the board?
Thanks in Advance!
Greetings
Olaf
23 March 2013 at 13:35 #115082
Olaf
Participant
@olaf
I the meantime i have got some more Informations.
FYI
Control signal interface
PIN Func Explain
1 EN Enable control signal
2 STEPX X Pulse signal
3 DIRX X Direction signal
4 STEPY Y Pulse signal
5 DIRY Y Direction signal
6 STEPZ Z Pulse signal
7 DIRZ Z Direction signal 18-25 GND GND
10 L1 Input limit interface 1
11 L2 Input limit interface 2
12 L3 Input limit interface 3
13 L4 Input limit interface 4
14 RLY Relay control signal
15 L5 Input limit interface 5
18 GND GND
19 GND GND
20 GND GND
21 GND GND
22 GND GND
23 GND GND
24 GND GND
25 GND GND

The drive using six DIP switch to setting current, segments, decay Mode
The current is better to closed to the motor rated current.
T1 T2 current
ON ON 20%*3.5A
OFF ON 50%*3.5A
ON OFF 75%*3.5A
OFF OFF 100%*3.5A

Segments Settings
When M1 = off, M2 = off, drive segments number is 1,1.8 ? step angle motor turning circle, the whole step = 200 steps / rev. When M1= OFF, S4 = ON,1.8 ? step angle motor turning circle, the whole step = 3200 steps / rev.

M1 M2 Segments
ON ON 1/8
OFF ON 1/16
ON OFF 1/2
OFF OFF 1

Decay Mode
Rapid decay is better when motor has a high speed.
D1 D2 Decay Mode
ON ON Rapid decay
OFF ON 50%Rapid decay
ON OFF 25%Rapid decay
OFF OFF Slow decay
1 April 2013 at 16:48 #115807
Royston
Participant
@royston
Hi

This is my first post but my be of help.

I have the same card, I am running mach3 on XP, my pin/port settings are:-

Motor output

X axis, enabled, step pin 2, dir pin 3, dir low x, step low y.

y axis, enabled, step pin 4, dir pin 5, dir low x, step low y.

z axis, enabled, step pin 6, dir pin 7, dir low x, sep low y.

Card dip settings :-

All three axis are the same

D1 on

D2 on

M1 on

M2 on

T1 on

T2 off

The three motors work ok.

I need help with the relay output. The relay light comes on with some settings when Mach3 is 'Reset' and goes out with other settings but I am unable to get any output from the terminals.

Royston
Author

Posts