G0 and G1

G0 and G1

This topic has 2 replies, 1 voice, and was last updated 13 February 2011 at 01:55 by Peter Saunders 1.

Viewing 3 posts - 1 through 3 (of 3 total)

Author

Posts
13 February 2011 at 01:38 #14943
Peter Saunders 1
Participant
@petersaunders1
variations in tool path
Advert

13 February 2011 at 01:38 #64005
Peter Saunders 1
Participant
@petersaunders1
In my experience it is sometimes of importance to note that the PATH from the start point and the end point when using G0 and G1 is often different.

In that, with G0 each axis travels at the same maximum rate (speed) until it reaches the destination of that axis. As in the example above starting at X0,Y0 and moving to X50.0,Y25.0 the Y axis will be reached before the X axis. Because both axis” are travelling at the same speed.

In the case of G1, the control manipulates the actual rate of each axis to achieve the correct fate of travel along the path. Using the same start point and finish point as above and nominating a feed rate (F) you will arrive at the XY point at the same time. It may not be an issue in most cases. but on occasion, there may be some part of the workpiece, clamp, etc. that is in the way. The solution is to simply to have your cutter far enough above the work and surrounds to address the possible issue. In my experience, while using the same cutter and moving positions to cut in different places, we only bought the tool to the rapid plane (.1000″) above the surface. We did have a few close calls on occasion (our machines were travelling at 15,000mm/min). Great articles.
13 February 2011 at 01:55 #64006
Peter Saunders 1
Participant
@petersaunders1
Well what an idiot would be. I posted the GO- G1 before reading Part 2. Part 2 of course explains the difference. MT sincerest apologies to the author.
Author

Posts

Viewing 3 posts - 1 through 3 (of 3 total)

Please log in to reply to this topic. Registering is free and easy using the links on the menu at the top of this page.

Code of Conduct

Latest Replies

Viewing 25 topics - 1 through 25 (of 25 total)

- Topic
- Voices
- Posts
- Last Post
- not so ‘run of the mill’?
  Started by: An Other in: Model Engineer.
- 4
- 5
- 31 January 2025 at 00:12
  Bazyle
- battery charger
  Started by: duncan webster 1 in: Electronics in the Workshop
- 13
- 23
- 30 January 2025 at 23:58
  Vic
- Christmas comes early !!
  Started by: Michael Gilligan in: The Tea Room
- 3
- 3
- 30 January 2025 at 22:22
  Nigel Graham 2
- OKMO Microcosm JO6B Miniature Stirling Engine
  Started by: Blue Heeler in: Miscellaneous models
- 1
- 1
- 30 January 2025 at 22:18
  Blue Heeler
- Had Another Go 1 2 … 13 14
  Started by: Nigel Graham 2 in: CAD – Technical drawing & design
- 22
- 338
- 30 January 2025 at 22:17
  Nigel Graham 2
- Drawing Standards 1 2
  Started by: John Stevenson 1 in: CAD – Technical drawing & design
- 22
- 33
- 30 January 2025 at 22:04
  HOWARDT
- Camel back straight edge
  Started by: me1 in: General Questions
- 12
- 23
- 30 January 2025 at 21:52
  peak4
- Early Myford Super-7B gear change wheels??
  Started by: flatline in: Beginners questions
- 7
- 16
- 30 January 2025 at 21:11
  flatline
- What Did You Do Today 2025 1 2
  Started by: JasonB in: The Tea Room
- 17
- 35
- 30 January 2025 at 21:07
  bernard towers
- CAD – Target Enigma 1 2 3
  Started by: SillyOldDuffer in: CAD – Technical drawing & design
- 17
- 67
- 30 January 2025 at 21:05
  Ian P
- The wonders of AI…
  Started by: Robin Graham in: The Tea Room
- 6
- 7
- 30 January 2025 at 20:45
  JohnF
- 16-Channel Analog Multiplexer Demultiplexer
  Started by: Michael Gilligan in: Electronics in the Workshop
- 4
- 8
- 30 January 2025 at 20:35
  Bazyle
- Shades of black humour
  Started by: JimmieS in: The Tea Room
- 10
- 10
- 30 January 2025 at 18:25
  Harry Wilkes
- Myford S7 VFD problem 1 2
  Started by: Glyn Davies in: Manual machine tools
- 17
- 27
- 30 January 2025 at 18:24
  Neil Lickfold
- Using Schneider ATV12 with remote terminal VW3A1006.
  Started by: chrismac in: Workshop Tools and Tooling
- 4
- 11
- 30 January 2025 at 17:14
  David Jupp
- Mind-Boggling Numbers
  Started by: Michael Gilligan in: The Tea Room
- 5
- 9
- 30 January 2025 at 16:22
  jaCK Hobson
- For Sale Voltera V1 PCB machine
  Started by: Redpiperbob in: General Questions
- 3
- 3
- 30 January 2025 at 15:26
  JasonB
- Transistor Circuit to Operate Relay from Arduino Uno 1 2
  Started by: James Alford in: Electronics in the Workshop
- 11
- 40
- 30 January 2025 at 13:38
  John Haine
- Fixing boiler cleading to firebox
  Started by: Peter Venn in: General Questions
- 6
- 6
- 30 January 2025 at 12:57
  duncan webster 1
- Emco Compact 5 Modifications 1 2 … 4 5
  Started by: Graham Meek in: Manual machine tools
- 12
- 108
- 30 January 2025 at 11:43
  Graham Meek
- Wicking felt for lathe headstock bearings
  Started by: YouraT in: Manual machine tools
- 10
- 25
- 30 January 2025 at 02:54
  Michael Gilligan
- building milling machine made from scrap part 1
  Started by: celso ari schlichting in: General Questions
- 1
- 6
- 29 January 2025 at 21:50
  celso ari schlichting
- Press Fit 1 2
  Started by: Peter Simpson 3 in: Beginners questions
- 18
- 26
- 29 January 2025 at 20:25
  Peter Simpson 3
- Pressure washer?
  Started by: Frank Gorse in: General Questions
- 10
- 19
- 29 January 2025 at 20:17
  Frank Gorse
- Stanley knives 1 2
  Started by: old fool in: The Tea Room
- 22
- 35
- 29 January 2025 at 19:51
  Robert Atkinson 2

Viewing 25 topics - 1 through 25 (of 25 total)

View full reply list.

Latest Issues

Issue 4761

February 2025

Buy Latest/Back Issues

Newsletter Sign-up

Latest Replies