Old lathe identification

Advert

New Replies

Report Bug

Help/FAQs

Old lathe identification

This topic has 10 replies, 7 voices, and was last updated 30 May 2022 at 09:55 by Hopper.

Viewing 11 posts - 1 through 11 (of 11 total)

Author

Posts
29 May 2022 at 14:44 #599809
paul rushmer
Participant
@paulrushmer83015
I rescued this from a scrap heap approximatly 18 inches long with a centre height of 2 1/2 inches, looks commercially made. I dont know wether it is a wood or instrument lathe. Spindle looks 1/2" BSW and solid Thanks Paul
Advert

29 May 2022 at 14:44 #14573
paul rushmer
Participant
@paulrushmer83015
29 May 2022 at 15:01 #599810
not done it yet
Participant
@notdoneityet
It appears to be a wood turning lathe – probably of anonymous maker. Likely home-made.

Edited By not done it yet on 29/05/2022 15:02:04
29 May 2022 at 17:46 #599828
David-Clark 1
Participant
@david-clark1
I would have said very old clock makers turns.
29 May 2022 at 23:20 #599877
Michael Gilligan
Participant
@michaelgilligan61133
A couple of points, but no identification
1. The base is very distinctive, which may aid identification as either a specific commercial lathe, or a ‘made from’
2. The nuts on the headstock mount have, perhaps, the right proportions for early Whitworth.
MichaelG.
30 May 2022 at 00:00 #599881
Nigel Graham 2
Participant
@nigelgraham2
The base does not look as if originally made for the lathe even if on this lathe from new. It might have come from a small milling-machine. That raising block – is it a casting? It looks like a piece of angle or Z-section found for the purpose.

What do the isolated nuts and bolts in the base hold?

Oh, probably commercially-made parts but the headstock doesn't seem quite to match in style to the saddle and tailstock. I wonder if it came from a different source; or perhaps the same manufacturer but a different model.

Intriguing and rather pretty little machine anyway, and it would be good to see it all bright and serviceable again, even if just for small items of wood-turning or brass-work by hand.

It was probably driven by treadle originally, possibly the type advertised as a "foot-motor" when sold as a stock item for driving any small machine.
30 May 2022 at 00:29 #599883
Hopper
Participant
@hopper
I would guess homemade from the way the heastock has been carved out of a piece of plate. Commercial offerings were usually cast as a matter of cost saving and simplicity of manufacture. Other components on it look fabricated from bar stock too.

Will make a nice piece all cleaned up.
30 May 2022 at 07:24 #599893
paul rushmer
Participant
@paulrushmer83015
Thanks for the thoughts so far, the head stock is a bronze casting, base is cast iron with plywood infill with mountings for motor so not origional and yes the mounting bracket is a lump of angle.

Thanks Paul
30 May 2022 at 09:13 #599903
vic newey
Participant
@vicnewey60017
Unusual to see a flat belt pulley on such a small lathe, V belts first appeared around1917 but much earlier pulleys for round leather belts are often thought to be for V belts as they fit very well.

Here someone has tried a V belt upside down? so the flat side is on the pulley but not sure how well that would work if at all
30 May 2022 at 09:19 #599906
David-Clark 1
Participant
@david-clark1
A timing belt would probably work well.
30 May 2022 at 09:55 #599912
Hopper
Participant
@hopper
The best flat-belt replacement I have found on my Drummond M-Type is running a Poly-V belt straight on the old flat belt pulleys. I run it with the V grooved side contacting the flat pulley. Works really well. Seems to grip well enough even without the V-grooves, including for taking 100 thou deep cuts in steel.
Author

Posts